Skip to content
Task, Pricing and Intelligent Pricing

Set up Intelligent Pricing and apply recommendations

You enable categories, set limits, and decide whether you approve every recommendation yourself or let STRYK work automatically within your limits.

Last updated: Revenue, Owner
Contents
  1. Before you start
  2. Ready in three steps
  3. Set up controls and categories
  4. Choose operating mode
  5. Review and apply recommendations
  6. Limits directly in the overview
  7. Market, history, forecast and calendar
  8. How to check the result
  9. If something does not work

Before you start

Ready in three steps

In STRYKPricingIntelligent Pricing

As long as STRYK has not yet calculated any recommendations, the view shows Ready in three steps.

  1. Choose Set up under Enable categories. The step shows how many categories are enabled, for example “1 of 4 enabled”. You do the enabling in the next section.
  2. Choose Switch on under Turn on Suggest. Afterwards the status reads “You decide on every price.”
  3. Choose Recalculate under First calculation. STRYK calculates recommendations for the coming days of the lookahead. As long as the mode is Off, this step has no button.

Completed steps are marked Done.

  1. Operating mode
  2. Recommendations
  3. Limits
  4. More

Set up controls and categories

In STRYKSettingsIntelligent Pricing

STRYK saves all values itself. The bar above the section offers Undo and Redo.

  1. In the Controls section, enter the Lookahead in days, the Increase and the Decrease in percent, the Daily limit (%) and the Min change. The example uses a 20% increase, a 15% decrease and a 5% daily limit.
  2. In the Categories section, choose the Nordlicht Double Room. The category expands.
  3. Enable Manage pricing. The category is then tagged Manage pricing, otherwise Inactive.
  4. Enter 139.00 € for the Minimum price and 249.00 € for the Maximum price. The minimum price must not be higher than the maximum price.
  5. For Automation, choose Use global mode, Recommendations or Observe only. With Use global mode, the category follows the operating mode. With Recommendations, you confirm every change in this category yourself.

The overall limits Increase and Decrease apply relative to the regular price, in addition to the Daily limit. Stricter limits of a category remain in effect. Under Advanced, you maintain further settings, for example on strategy, events and market signals.

Choose operating mode

In STRYKPricingIntelligent Pricing

The Operating mode switch has the positions Off, Suggest and Automatic. The line below describes the state, for example “Suggest is active. You decide on every price.” With Off, prices that are already set remain in place.

  1. Choose Suggest so that STRYK calculates recommendations and you approve each one yourself.
  2. Optional: choose Automatic so that STRYK applies suitable price changes itself within your limits. A confirmation shows the price corridor, the Daily limit (%) and the Approved scope for each category.
  3. Choose Automatic in the confirmation. With Cancel, the previous mode remains.

For Automatic, enable at least one category: Manage pricing is active and Automation is set to Use global mode. Automation sets room prices within your limits. For data problems, STRYK shows the reason under Data basis, for example that too few evaluated forecasts are available.

Review and apply recommendations

In STRYKPricingIntelligent Pricing

In the Recommendations section, each recommendation shows the date, the category, the recommended price and the change. The example: for 18.12.2026, STRYK recommends 177.45 € instead of 169.00 € for the Nordlicht Double Room, that is +5.00%.

  1. Choose the date of the recommendation. The details show Current price, Recommended price, Change, Regular price, Last run, Confidence and the reasons.
  2. Choose Apply to set the price, or Discard.
  3. Optional: enable Select all for several recommendations or mark them individually. Then choose Apply with the number.

With Filters, narrow down by Change (All, Increase, Decrease), Category as well as From and Until. With Recalculate, STRYK starts a new calculation.

Limits directly in the overview

In STRYKPricingIntelligent Pricing

The Limits section shows the Daily limit, Maximum increase and Maximum decrease, each between 1 and 50%. Enter a value and STRYK saves it itself. Price limits per category opens the settings.

Market, history, forecast and calendar

In STRYKPricingIntelligent Pricing

The More section opens four views:

  • Market shows competitor prices and market signals. With From and Until, you narrow down the period.
  • History lists applied and discarded recommendations with their status.
  • Forecast shows occupancy and price per day.
  • Calendar shows the prices per day and category. Here you can only view.

How to check the result

The figures Open recommendations and Applied in 30 days count the status. Applied prices appear in the price calendar: Set day rates in the calendar. The History shows every decision. Calculate a stay with Check price: Check a price preview for a stay.

If something does not work

What you seeCauseHow to fix it
“Price limits conflict. Please check the settings.”The limits of a category conflict.Choose Set up and correct the minimum or maximum price.
“Some recommendations could not be applied. Please check the current status.”STRYK rejected part of the application.Choose Recalculate and check the status.
“The application was not confirmed. Please check the current status in the history.”The response to the application is missing.Open the History and do not apply again.
“The settings have been changed in the meantime. Load the latest version and check your entry again.”Someone changed the settings at the same time.Choose Load latest version.
“The minimum price must not be higher than the maximum price.”The minimum price is higher than the maximum price.Correct the values.
“The scope of automation could not be confirmed. Please reload the current settings.”STRYK has not confirmed the scope of automation.Reload the settings.
“No open recommendations”There is nothing to check, or the mode is Off.Choose Suggest and then Recalculate.
Questions about STRYK?